Käferlein Loop AMA-87 17-80m, 100W
Available in 15 days
Supply Scope
- Antenna
- Pole mount for vertical installation, max. 60 mm pole diameter
- Control unit
- Power cable for control unit
- Plug for control cable (Hirschmann STAS200 on antenna, 3.5 mm jack mono on control unit)
- Printed manual in German
Download
AMA Magnetic Loops - Principle of construction
The main feature of a magnetic loop is it's comparably small size in relation to the wavelength. This makes this type of antenna very attractive to many radio amateurs with little space for aerials. The tuning is done with a high voltage capacitor in the loop, which is made from aluminium tubing. For best convenience the capacitor is tuned remotely by an electric motor.- A magnetic loop antenna must be weatherproof for operation outside a building. The selection of materials and construction of the joints are of high importance. By many practical experiments the best suitable materials have been selected.
- The tube of the loop and the tuning capacitor must be constructed very robust, to avoid fluctuations of the inductivity and capacity and therefore fluctuations of the resonant frequency. Besides the mechanical stability the tuning capacitor must be built with thick plates, a solid axle and large electrical contacts to prevent heating from the high electrical currents. The also keeps losses at a minimum.
- For a precise tuning an accurate and continues mechanical drive, free of play, should be used. This mechanical drive must work reliably under all weather influences.
- The magnetic loop antenna should withstand excess power without permanent damage. This requires that the insulating material of the capacitor is resistive against high voltages, leak currents and arcing. When the antenna is accidentially overloaded there will only be a flash arc between the capacitor plates, but the antenna itself will not be damaged.
From July 2017 on, all antennas with a loop diameter larger than 1.2m are shipped with a support tube. This support tube varies in size and material (aluminium, steel) depending on the size of the antenna. It runs vertically through the antenna. The support is fixed to the antenna mount at the bottom, and to the protective cover of the capacitor at the top. It relieves the loop from strong side loads at high windspeeds.
The models of the AMA Loop Antennas
The current delivery time can be found in the listing below.
Product Name | AMA-87 |
---|---|
Efficiency 18 MHz | 96 |
Efficiency 10 MHz | 79 |
Bandwidth 3.5 MHz (kHz) | 3 |
Bandwidth 7 MHz (kHz) | 11 |
Bandwidth 10 MHz (kHz) | 23 |
Bandwidth 14 MHz (kHz) | 46 |
Bandwidth 18 MHz (kHz) | 75 |
Efficiency 3.5 MHz | 10 |
Efficiency 7 MHz | 53 |
Efficiency 14 MHz | 92 |
Mono-/Multiband | Multiband |
Number of Turns | 1.0000 |
Brand | AMA Käferlein |
Supported Bands | 80m, 40m, 30m, 20m, 17m |
Loop Diameter | 1.3 m |
Max. Power [W] | 100 W |
Frequency Range | 3.5 - 18.17 MHz |
Polarisation | Vertical |
Antenna Type | Omni-directional Antenna |
Design of antenna | Magn. Loop |
Gain [dBi] (free space) | 80 m: -6.9; 40 m: -1; 30 m: 0.8; 20 m: 1.4; 17 m: 1.6 |
Gain 3.5 MHz [dBi] | -6.9 |
Gain 7 MHz [dBi] | -1 |
Gain 10 MHz [dBi] | 0.8 |
Gain 14 MHz [dBi] | 1.4 |
Gain 18 MHz [dBi] | 1.6 |