Notizen
Gliederung
FT847-SuperControl
CAT control software for the YAESU™ FT-847® amateur radio transceiver
Author: Peter Pfisterer, DH1NGP
Web: www.supercontrol.de
Free support hotline: hotline@supercontrol.de
Distribution Germany :
WiMo Antennen und Elektronik GmbH
Am Gaexwald 14
D-76863 Herxheim
Tel. (07276) 96680 Fax. (07276) 6978
Internet: www.wimo.com e-Mail: info@wimo.com
Full transceiver control for the FT-847
Full transceiver control via buttons in the software. Frequency and mode will be polled automatically from the transceiver. So a normal tuning on the transceiver itself will be detected and shown in the software vfo’s.
Comfortable memory management
Open memory database with an unlimited amount of possible memories in an overall view. The memory banks of all amateur radio bands are visible and useable with ease at the same time. Several additional memory banks are available. Also memory banks with the possibility to save offset, DCS, DEC, ENC and Easycomm-data are available. The easycomm-data can be sent to another serial port to drive easycomm-compatible hardware like rotors and much more.
Transverter on-screen translation
Programable calculated target frequency’s on two additional software vfo-display’s, for the use with up to four optional transverter-devices. The software is capable to administrate up to four transverter-devices (for each antenna-jack).
Automatic Doppler correction via NOVA®
info: www.nlsa.com
DDE-interface (Dynamic Data Exchange) to satellite-tracking programs (NOVA®, etc.) for automatic Doppler-correction. The Doppler-corrected frequency will be send to the transceiver, so no manual tuning is needed anymore, when working satellites. RX- and TX-VFO will be continuously updated with doppler-corrected data. Of course, possible calculated transverter frequencies will be taken as source for the final calculation of the doppler shift. So this part is 100% compatible with AO-40 or other super-high frequency satellites. Various possibilities to alter the way to calculate the doppler shift itself are available in the settings.
Clone data memory management for the internal memories of the FT-847
Clone data memory-management for the internal memories of the FT-847® transceiver. FT847-SuperControl®  is able to read, edit, archive and send back clone files to the transceiver. It’s easy to set up different clone files and copy them on your harddrive. If you want to use special setup’s in the transceiver, simply send the wanted  clone file to the rig. Clone files can be edited with the help of existing FT847-SuperControl® memory banks of course.
Wave recording of QSO‘s or other important signals for the FT-847
Wave recording of qso's or other important signals. FT847-SuperControl®  has the possibility to record signals either when the squelch has been opened or on other choosable events. For this feature, a standard sound-card in the computer is necessary. The recorded data will be saved automatically to a special drawer and can be replayed at any time
Scanning of single memory banks for the FT847-transceiver
Scanning of single memory banks, there is no need to scan all memory banks at the same time. Your FT-847 transceiver  has only 100 internal memories, which must be scanned all at once. If you’ve saved frequencies out of different bands and if you want to scan these memories, you ‘ll hear a rapid clicking of relais-type-devices in the transceiver. It is not proved, but we’re sure, that continuous long time period scanning, will shorten the life of these relais type devices. This part has a skip function for single memories not to be scanned, but needed to stay in memory bank.
Full featured VFO - scanner
Full featured vfo scanner with software based quick memory bank - function (QMB). It’s possible to set up different scan ranges which can be scanned in a row. Every found signal will be taken to the quick memory bank for a later evaluation. You can specify the s-meter level at which the frequencies should be saved.
Full featured visual bandscope
Visual band scope with different scan-steps and various possibilities. Take over a desired frequency to the actual VFO with just one mouseclick.
Additional features:
FT100-SuperControl
CAT control software for the YAESU™ FT-100® transceiver